• About
  • Contact
  • Privacy Policy
SecurityCamCenter.com
  • Home
  • Buying Guide
  • Learning & Tips
  • Technical Guides
  • Security Tips
  • Downloads
  • CCTV Glossary
No Result
View All Result
SecurityCamCenter.com
No Result
View All Result
Home Technical Other

How to reset ADC Alarm.Com cameras

Marco Albertini by Marco Albertini
in Other

Alarm.com runs their OEM line of ADC cameras that are easy to reset. However, each ACD camera has a slightly different reset procedure that depends on the type of the camera. Most of the ADC can be factory reset by pressing and holding the reset button for a few seconds.

After the factory reset is performed on an ADC camera, the device should remain plugged-in and you have to wait for at least two (2) minutes. Once the connection comes back, the camera should be on factory default settings.

How to reset ADC Alarm.Com cameras

Thing to keep in mind when resetting an ADC Alarm.Com camera:

  • Before doing a reset on any Alarm.com ADC camera, you should wait at least two minutes after the device has been powered on. Attempting to perform a factory reset before the camera has fully powered on could cause the reset to fail which means you have to do it again.
  • Factory resetting an Alarm.com ADC camera will NOT delete it from an account. You will still need to remove/delete the camera from the existing account before you will be able to add it to a new one.

ADC Alarm.Com Camera Reset Procedure

The factory reset processes for most ADC Alarm.Com cameras are listed below. If the camera model is not included on this list, a reset is usually done by pressing and holding the reset button for 15 seconds to 60 seconds depending on the camera model.

For more detailed information, you can consult the user guide of your camera. Note: Source for the list below is Alarm.com.

ADC-V700X Reset Procedure

Press and hold the reset button inside the back of the camera until the LED light on the device rapidly flashes red. This will take about 90 seconds.

ADC-V510 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red. This will take about 60 seconds. You will need a paperclip to press and hold the reset button.

ADC-V610PT Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red. This will take about 60 seconds. You will need a paperclip to press and hold the reset button. The reset button can be found underneath the camera.

ADC-VS1 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red. This will take about 60 seconds. You will need a paperclip to press and hold the reset button.

2GIG CAM-HD100 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes yellow. This will take about 10 seconds.

ADC-VS120 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-VS420 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-V520 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-V521IR Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 10 to 15 seconds. The reset button is found on the back of the camera.

ADC-V522IR Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 10 to 15 seconds. The reset button is the same as the WPS button, and it is found on the back of the camera.

ADC-V523 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The reset button is the same as the WPS button, and it is found on the camera’s underside.

ADC-V620PT Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-V622-WELL Reset Procedure

Press the Menu button, and then use the Volume buttons to locate the Factory Reset option. Select this option, and follow the audio prompts to perform the reset.

ADC-V720 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds.

ADC-V720W Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The reset button is the same as the WPS button.

ADC-V721W Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The reset button is the same as the WPS button.

ADC-V722W Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The reset button is the same as the WPS button.

ADC-V723 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The reset button is the same as the WPS button, and it is found on the camera’s underside.

ADC-VC725 Reset Procedure

Power down the camera by disconnecting its power supply. Use a paperclip or a similar thin object to press and hold the reset button while simultaneously powering on the camera. The reset button will make a small clicking noise when pressed so that you know it is being held down. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-VC726 Reset Procedure

Power down the camera by disconnecting its power supply. Use the included hex key for the camera to remove the water-tight door for the camera at its bottom. Press and hold the reset button found underneath the door while simultaneously powering on the camera. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-VC736 Reset Procedure

Power down the camera by disconnecting its power supply. Remove the water-tight door for the camera using a Phillips head screwdriver. Press and hold the reset button found underneath the door while simultaneously powering on the camera. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-V820 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. The black reset button is inside the camera on the back.

ADC-V821 Reset Procedure

Press and hold the reset button on the device until the LED lights blink red. This will take about six (6) seconds. The reset button is found on the main circuit board inside the camera.

ADC-VC825 Reset Procedure

Power down the camera by disconnecting its power supply. Unscrew the camera cover and remove it. Press and hold the reset button underneath the cover while simultaneously powering on the camera. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-VC826Reset Procedure

Power down the camera by disconnecting its power supply. Unscrew the camera cover and remove it. Press and hold the reset button underneath the cover while simultaneously powering on the camera. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-VC836 Reset Procedure

Power down the camera by disconnecting its power supply. Remove the water-tight door for the camera using a Phillips head screwdriver. Press and hold the reset button found underneath the door while simultaneously powering on the camera. Continue to hold the reset button for at least ten (10) seconds to ensure that the reset goes through successfully.

ADC-SVR100 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-SVR122 Reset Procedure

Press and hold the reset button on the device until its LED light rapidly flashes red and green. This will take about 15 seconds. You will need a paperclip to press and hold the reset button.

ADC-CSVR126 Reset Procedure

Access the local interface for the device. Click the menu icon, which is the three (3) horizontal bars. Choose System, followed by Factory Reset. You may need to provide the password for the device. Click Next to proceed with the reset. The device must be re-enrolled with an Alarm.com account following a factory reset.

Alarm.com SkyBell Reset Procedure

Press and hold the main SkyBell button until the button begins flashing blue. This will take about 50 seconds.

Source: Alarm.Com official website. 

Marco Albertini

Marco Albertini

Italian-born Marco Albertini, with a background in Computer Science, found his passion in security camera systems, alarms, and cloud services. Based in New York since 2010, he's a sought-after expert, assisting numerous businesses and homeowners in securing their properties with advanced solutions.

Related Posts

Luma Technical Guides

Luma Default Password

3xLogic Default Password

3xLogic Default Password

Axis Technical Guides

Axis Default Password

Load More

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Latest articles

Hikvision

How to Reboot Your Hikvision Recorder Remotely

Hikvision

Hik-Connect App Cannot Playback between 23:00 and 23:59 (Quick Solution)

Learning & Tips

Top Methods for Detecting and Preventing Car Break-Ins (2023)

How To Fix

How to reset Ring Stick-Up Camera (2023 Methods)

Learning & Tips

Motion Sensors Types And How Do They Work (Guide)

SecurityCamCenter is a participant in the Amazon Services LLC Associates Program. This post may contain affiliate link(s). An affiliate link means we may earn advertising or referral fees if you make a purchase through our links, at no extra cost to you.

Categories

© 2023 SecurityCamCenter.com / Security Tips and Tutorials

No Result
View All Result
  • Home
  • Buying Guide
  • Technical

© 2022 SecurityCamCenter.com / Security Tips and Lessons